The Adco Olefin HD RV Cover for Travel Trailers up to 20' - All Climate + Wind - Gray # AD97ZR has a 3-year warranty and fits trailers between 22" and 24' long. If you measure the length of your Micro-Lite and take into consideration the rear ladder and it's not longer than 24' the cover will work well for you.
Please let me know if it ends up being longer than 24' and we I can make additional recommendations. view full answer...
The Stromberg Carlson Bike Bunk Trailer-Mounted Bike Rack Carrier for A-Frame Trailers - 2"-100lbs Item # CC-275 has a max weight capacity of 100lbs so it wouldn't be able to support the bike rack and 4 bikes.
Instead you can install a Curt Adjustable Trailer Hitch Receiver - 18"-51" Wide - 2" Drop - Class III - 2" Item # C13701 if your frame distance falls between 18-51", if not let me know and we can find an alternative.
Once you have the hitch installed you can insert the Swagman... view full answer...
I found the installation instructions for your ZX25 and the mounting dimensions are 7.59 tall x 6.69 wide so the IRV RV Stereo part # IRV34 is the best replacement compared to the others as far as fit goes. It measures 7-3/4" wide x 7-1/2" tall x 5" deep. I have attached a video for your reference.
If you would like to measure the back of the stereo to be certain of these mounting dimensions, I can make sure this is the best replacement. view full answer...
It sounds like you need the Go Power Overlander Expansion Kit part # 34282182 which a 190 Watt Monocrystalline solar cell solar panel. This kit will expand your Solar Elite, Weekender ISW, Solar AE-6, Solar Flex, Overlander or Retreat Go Power system with the included branch connectors. We also have the extension cables part # 34276216 for 10 ft, part # 34279532 for 15' and part # 34276215 for 30 ft.
We also have the Go Power Retreat Expansion Kit - 100 Watt Solar Panel part # 34272634. view full answer...
The Replacement Rubber Cap # 37262105 is designed to fit over a brass city water inlet like the RV City Water Inlet # 372321-B-36-A. The notch in the rubber cap will only allow for a limited amount of room to fit over the city water inlet.
If you have an inlet like the RV City Water Inlet # 372160-85-A-26A you will not be able to fit the cap over the inlet. The plastic is affixed to where it cannot be removed from the inlet. You can attach the cap by drilling a small hole into the strap... view full answer...
When it comes to the Snap-In RV Curtain Carriers - Qty 14 # 37281455 you can just pop them off with a flat head screw driver or some pliers.
The new ones will just snap into place once the old are removed.
You can see in the linked video about snap tape where he snaps one off and on. view full answer...
Screen door latches are pretty much universal so you really just need to ensure that you're selecting the correct direction, but no manufacturer follows the same point of view when labeling their directions so the key is to look at the plunger.
If you're standing outside of your trailer looking in and your handle needs to be on the left then you'll want the Door Latch for Amerimax RV Screen Doors - Right Hand # 37210765.
If you're standing outside of your trailer looking in and your... view full answer...
The SC97VR is not a fit for the 2019 RAM 2500 and there are no backup cameras that will tie into the factory wiring on your truck. Your best bet is to install a universal backup camera that uses a different monitor than your truck's OEM screen.
I recommend going with the Rear View Safety WiFi Hitch Backup Camera System - Wireless # RVS-83112-WiFi. This system is completely wireless with a rechargeable battery and built-in WIFI connection (pre-existing WIFI is not necessary, so it works... view full answer...
If the height of the I-beams is less than 6" as you say then you would have to have to swap out the regular safety struts for the Mount-n-Lock SafetyStruts Universal RV Bumper Support Brackets # MO34VR, which include spacers to place the brackets far enough out to clear the flange lip. You would not want to trim the flange of your trailer frame beams.
You can place the supports on the inside or the outside of the frame beams as the difference between the two sides really isn't going to... view full answer...
I believe you are asking how to remove the lens of the Low Profile RV Combination Tail Light - Stop, Tail, Turn - 9 Diodes - Passenger Side part # RVSTL60. You will push in the two white tabs on the sides of the lights that have a cut out in the plastic and gently pull on the lens until it pops off. The replacement lens is part # AST60B.
If that is not what you meant by RV light cover please let me know. view full answer...
Yes, since the jaws are what will be holding the items they will be able to handle 15 lbs of weight.
The Quick Fist Mini Clamps # QF30050 are rated for 25 lbs each so 15 lbs will not be a problem at all. view full answer...
Go To Results